Difference between revisions of "HOWTO Change the Thread on the Husqvarna Designer SE"

From i3Detroit
Jump to: navigation, search
(Added information on the bobbin and its tensioning.)
Line 1: Line 1:
This mini-tutorial describes how to change the thread on the [[Husqvarna Designer SE]].
+
This mini-tutorial describes how to change the thread, rewind bobbins, and adjust the bobbin tension on the [[Husqvarna Designer SE]].
  
Always use embroidery thread in the Husqvarna!  There is a specially-marked black box containing embroidery thread stored to the right of the machine, or in the drawers under the machine.  ''Embroidery thread should be glossy and may be marked as embroidery-only on the bobbin.  If in doubt, ask!''
+
'''To change the spool (embroidery) thread:'''
  
'''To change the thread:'''
+
1.  Raise the upper spool by gently pulling outward.   
 
+
1.  Raise the upper bobbin by gently pulling outward.   
+
  
 
[[File:HusqvarnaDesignerSE LoadThread 1.jpg|600px]]
 
[[File:HusqvarnaDesignerSE LoadThread 1.jpg|600px]]
Line 11: Line 9:
 
2.  Remove the end cap; pull off the old spool, and pull the thread out of the machine.
 
2.  Remove the end cap; pull off the old spool, and pull the thread out of the machine.
  
3.  Put a new spool on the upper bobbin.  Replace the end cap with the tines pointing inward.
+
3.  Put a new spool on the upper spool.  Replace the end cap with the tines pointing inward.
  
 
[[File:HusqvarnaDesignerSE LoadThread 2.jpg|600px]]
 
[[File:HusqvarnaDesignerSE LoadThread 2.jpg|600px]]
Line 26: Line 24:
 
6.  Thread the needle using tweezers, or use the attached needle threader.  ''Instructions are not yet detailed here.  An illustrated diagram will be added as time permits.''
 
6.  Thread the needle using tweezers, or use the attached needle threader.  ''Instructions are not yet detailed here.  An illustrated diagram will be added as time permits.''
  
TODO: Add instructions for rewinding the bottom bobbin and changing the bottom bobbin.
+
'''To change the bobbin (lower) thread:'''
 +
 
 +
1.  Pull off the clear plastic bobbin cover plate.
 +
 
 +
[[File:HusqvarnaDesignerSE_BobbinCoverPlate.JPG|600px]]
 +
 
 +
2.  Pull out the round bobbin. 
 +
 
 +
[[File:HusqvarnaDesignerSE_Bobbin.JPG|600px]]
 +
 
 +
'''WARNING''': Use ONLY bobbin thread for filling bobbins.
 +
 
 +
The repair shop specially recommended the use of Robison-Anton filament poly bobbin thread.  The spools are stocked in the same stack as the rest of the sewing supplies.
 +
 
 +
For instructions on how to fill a bobbin with thread using the Husqvarna's winding capabilities, see below.
 +
 
 +
[[File:HusqvarnaDesignerSE_BobbinThread.JPG|600px]]
 +
 
 +
3.  With the 'D' or 'H' on the spool facing up, place the bobbin in the slot.  Wind the thread into the slots as in the picture below; there's no need to worry about where the thread goes after it's caught in the third slot.  Replace all covers.
 +
 
 +
[[File:HusqvarnaDesignerSE BobbinRethreadingDiagram.jpg|600px]]
 +
 
 +
'''To wind a bobbin with thread'''
 +
 
 +
1.  With the 'D' or 'H' on the spool facing up, place an empty bobbin on the bobbin winder.
 +
 
 +
[[File:HusqvarnaDesignerSE-PlaceBobbinOnWinder.JPG|600px]]
 +
 
 +
2.  Place bobbin thread on the upper spool; rotate it into the upright position.  (You may need to move the white disklike spool support up before you can move the spool.)
 +
 
 +
As noted above, use ONLY bobbin thread for filling bobbins.
 +
 
 +
3.  Run the thread in the path shown below.  Fasten it around the bobbin by running it around four or five times.
 +
 
 +
[[File:HusqvarnaDesignerSE-BobbinWinderThreadPath.GIF|600px]]
 +
 
 +
4.  Push the bobbin winder lever forward. 
 +
 
 +
[[File:HusqvarnaDesignerSE-BobbinWinderOn.JPG|600px]]
 +
 
 +
5.  The winding dialogue will popup on the LCD.  Press 'Start' to begin winding.
 +
 
 +
You may need to adjust the speed to about half.
 +
If the bobbin spins without engaging the thread, try grabbing the loose end and holding it still for a second.
 +
 
 +
[[File:HusqvarnaDesignerSE-BobbinWinderDialogue.JPG|600px]]
 +
 
 +
'''To adjust the bobbin tension:'''
 +
 
 +
The top (embroidery) spool sets tension using the dialogues in the Husqvarna.  However, the tension on the bottom bobbin must be set manually.
 +
 
 +
Please note that you'll only ever need to change the bobbin tension if you're showing large amounts of white bobbin thread in your embroidery.  You'll need to experiment to get the right setting.
 +
 
 +
1.  As when replacing the bobbin, remove the bobbin's protective cover.
 +
 
 +
2.  Remove the needle plate.
 +
 
 +
[[File:HusqvarnaDesignerSE_NeedlePlate.JPG|600px]]
 +
 
 +
3.  Remove the horseshoe-shaped cover over the bobbin case.
 +
 
 +
[[File:HusqvarnaDesignerSE_BobbinCover.JPG|600px]]
 +
 
 +
4.  Remove the bobbin and bobbin case.
 +
 
 +
 
 +
[[File:HusqvarnaDesignerSE_BobbinCase.JPG|600px]]
 +
 
 +
5.  Find the flat-head screw set in the side of the bobbin case.  Rotate it ''at most an eighth-turn''; very small rotational changes produce surprisingly large tensioning changes.
 +
 
 +
[[File:HusqvarnaDesignerSE_BobbinCase2.JPG|600px]]
 +
 
 +
6.  Replace all components.  Run a test scrap.

Revision as of 17:49, 11 May 2014

This mini-tutorial describes how to change the thread, rewind bobbins, and adjust the bobbin tension on the Husqvarna Designer SE.

To change the spool (embroidery) thread:

1. Raise the upper spool by gently pulling outward.

HusqvarnaDesignerSE LoadThread 1.jpg

2. Remove the end cap; pull off the old spool, and pull the thread out of the machine.

3. Put a new spool on the upper spool. Replace the end cap with the tines pointing inward.

HusqvarnaDesignerSE LoadThread 2.jpg

4. Pull the thread into the path indicated by the arrows. It should catch there. If you get it wrong, just tug gently to correct, or pull the thread out entirely and try again.

HusqvarnaDesignerSE LoadThread 3.jpg

5. Be sure to pull the thread through the small metal loop just above the needle.HusqvarnaDesignerSE LoadThread 4.jpg

6. Thread the needle using tweezers, or use the attached needle threader. Instructions are not yet detailed here. An illustrated diagram will be added as time permits.

To change the bobbin (lower) thread:

1. Pull off the clear plastic bobbin cover plate.

HusqvarnaDesignerSE BobbinCoverPlate.JPG

2. Pull out the round bobbin.

HusqvarnaDesignerSE Bobbin.JPG

WARNING: Use ONLY bobbin thread for filling bobbins.

The repair shop specially recommended the use of Robison-Anton filament poly bobbin thread. The spools are stocked in the same stack as the rest of the sewing supplies.

For instructions on how to fill a bobbin with thread using the Husqvarna's winding capabilities, see below.

HusqvarnaDesignerSE BobbinThread.JPG

3. With the 'D' or 'H' on the spool facing up, place the bobbin in the slot. Wind the thread into the slots as in the picture below; there's no need to worry about where the thread goes after it's caught in the third slot. Replace all covers.

HusqvarnaDesignerSE BobbinRethreadingDiagram.jpg

To wind a bobbin with thread

1. With the 'D' or 'H' on the spool facing up, place an empty bobbin on the bobbin winder.

HusqvarnaDesignerSE-PlaceBobbinOnWinder.JPG

2. Place bobbin thread on the upper spool; rotate it into the upright position. (You may need to move the white disklike spool support up before you can move the spool.)

As noted above, use ONLY bobbin thread for filling bobbins.

3. Run the thread in the path shown below. Fasten it around the bobbin by running it around four or five times.

HusqvarnaDesignerSE-BobbinWinderThreadPath.GIF

4. Push the bobbin winder lever forward.

HusqvarnaDesignerSE-BobbinWinderOn.JPG

5. The winding dialogue will popup on the LCD. Press 'Start' to begin winding.

You may need to adjust the speed to about half. If the bobbin spins without engaging the thread, try grabbing the loose end and holding it still for a second.

HusqvarnaDesignerSE-BobbinWinderDialogue.JPG

To adjust the bobbin tension:

The top (embroidery) spool sets tension using the dialogues in the Husqvarna. However, the tension on the bottom bobbin must be set manually.

Please note that you'll only ever need to change the bobbin tension if you're showing large amounts of white bobbin thread in your embroidery. You'll need to experiment to get the right setting.

1. As when replacing the bobbin, remove the bobbin's protective cover.

2. Remove the needle plate.

HusqvarnaDesignerSE NeedlePlate.JPG

3. Remove the horseshoe-shaped cover over the bobbin case.

HusqvarnaDesignerSE BobbinCover.JPG

4. Remove the bobbin and bobbin case.


HusqvarnaDesignerSE BobbinCase.JPG

5. Find the flat-head screw set in the side of the bobbin case. Rotate it at most an eighth-turn; very small rotational changes produce surprisingly large tensioning changes.

HusqvarnaDesignerSE BobbinCase2.JPG

6. Replace all components. Run a test scrap.