Difference between revisions of "Category:Fab Lab"

From i3Detroit
Jump to: navigation, search
(Added TODO list.)
Line 38: Line 38:
 
|-  
 
|-  
 
| Protomat CNC  || TBD  
 
| Protomat CNC  || TBD  
 +
|}
 +
 +
== TODO List ==
 +
The following list is an attempt to offer up suggestions of tasks that could be accomplished in the Fab Lab by people interested in helping out.
 +
 +
Feel free to take charge of one or more of these items as your time and expertise allow. If you have taken charge of a task, please put your name into the field next to the task.
 +
 +
'''Should you run out of time or ability to complete a task, make sure to post on [mailto:i3detroit@googlegroups.com the mailing list] and "fail loudly".''' This ensures that task status is shared, and no task languishes in silent failure.
 +
 +
 +
{| class="wikitable"
 +
! Task Name
 +
! Description
 +
! Priority
 +
! Champion
 +
|-
 +
| Manufacture Focus Gauge for [[Full_spectrum_Laser_Cutter|FS Laser]]
 +
| A sturdy, solid, non-deformable block 1.359" (critical dimension) tall and nominally 0.75" diameter (or square). Chamfered or filetted corners for comfort.
 +
| 1
 +
|
 +
|-
 +
| Get [[PCB_Mill|Protomat]] Working
 +
| The VM for the Protomat has not yet been completed and verified to function as a controller.
 +
| 2
 +
|
 +
|-
 +
| Get Third Shelf Installed
 +
| Five suitable brackets for the shelf stanchions need to be obtained, installed, and the shelf put upon them. The third shelf should be somewhat closer to the upper shelf than the lower.
 +
| 2
 +
|
 +
|-
 +
| Patch Ceiling
 +
| The removal of the old PVC ventilation ducting left a hole in the ceiling of the lab, with a PVC ring still in place. Removal of the ring is desired. There is an 8" square patch and patch compound available in the cabinet under the Protomat. The patch should also cover the two smaller holes further over the shelf.
 +
| 3
 +
|
 +
|-
 +
| Mount Flash Card Reader
 +
| The flash card reader currently sits on top of the old Fab Lab PC. A better place would be mounted underneath the shelf near the monitor, with the most useful slots facing outwards.
 +
| 4
 +
|
 +
|-
 +
| [[Printrbot]]
 +
| The Printrbot sits, alone and unloved, jealous of its successor the [[Rostock MAX]]. Bring a little love and joy into its world by repairing it, replacing the firmware with Repetier, getting a VM set up for it, and generally making it a more useful machine again.
 +
| 4
 +
|
 +
|-
 +
| Replace USB Hub
 +
| The current USB hub used by the Fab Lab server sucks. Suggested replacement would be one or two USB2.0 self-powered hubs. If two, one would be mounted on the underside of the bottom shelf near the monitor for flash drives and such, and the other tucked away hidden for machine interfaces.
 +
| 4
 +
|
 +
|-
 +
| Relocate Pegboard
 +
| The pegboard hanging on the wall behind the office-side door is a much-appreciated secret donation. However, being behind the door is a less-than-useful location. A good target for this would be on the opposite wall, under the shelf and between the Protomat and the Rostock MAX.
 +
| 4
 +
|
 +
|-
 +
| Rehang Corkboard
 +
| The corkboard on the wall hangs from a board, rather than being flush to the wall. This causes the board to swing when bumped.
 +
| 5
 +
|
 +
|-
 +
| Decorative Work
 +
| The Fab Lab currently has a sort of forest theme going on. It would be nice to continue the theme by painting the conduits and stanchions deep brown to simulate vines and trunks, put up more vinyl leaves, and paint the ceiling with either a sky pattern or a forest canopy pattern.
 +
| 5
 +
|
 
|}
 
|}
  

Revision as of 16:14, 11 October 2013

The Fab Lab

Contents

Welcome

Welcome to the fab lab! If you don't know what something does, please ask. The Zone Warden is Andrew Meyer. The zone warden sign is here: File:FabLabZonePoster.docx

Tools in this zone:

Printrbot

Rostock MAX

LPK C30/S (PCB Mill)

Full Spectrum Laser Cutter

Tools that are in the Fab Lab Annex (next to Laser Cutter Zone)

Stratasys FDM 1650

Vacuum Former

Pricing

To cover the cost of consumables/maintenance, please contribute when you use the Fab Lab equipment. Put money in the blue bin labeled "3D printer fund."

ABS for 3D printing is priced by gram or cubic centimeter of extruded plastic. Please include all the test extrusions and failed prints in your measurements.

Laser time is measured based on laser firing time. Use the timer on the laser cutter display.

Equipment Price
3mm ABS (printrbot) 5¢/gram or cm^3
1.75mm ABS (Rostock) 10¢/gram or cm^3
FSLaser time 25¢/min cut time
Protomat CNC TBD

TODO List

The following list is an attempt to offer up suggestions of tasks that could be accomplished in the Fab Lab by people interested in helping out.

Feel free to take charge of one or more of these items as your time and expertise allow. If you have taken charge of a task, please put your name into the field next to the task.

Should you run out of time or ability to complete a task, make sure to post on the mailing list and "fail loudly". This ensures that task status is shared, and no task languishes in silent failure.


Task Name Description Priority Champion
Manufacture Focus Gauge for FS Laser A sturdy, solid, non-deformable block 1.359" (critical dimension) tall and nominally 0.75" diameter (or square). Chamfered or filetted corners for comfort. 1
Get Protomat Working The VM for the Protomat has not yet been completed and verified to function as a controller. 2
Get Third Shelf Installed Five suitable brackets for the shelf stanchions need to be obtained, installed, and the shelf put upon them. The third shelf should be somewhat closer to the upper shelf than the lower. 2
Patch Ceiling The removal of the old PVC ventilation ducting left a hole in the ceiling of the lab, with a PVC ring still in place. Removal of the ring is desired. There is an 8" square patch and patch compound available in the cabinet under the Protomat. The patch should also cover the two smaller holes further over the shelf. 3
Mount Flash Card Reader The flash card reader currently sits on top of the old Fab Lab PC. A better place would be mounted underneath the shelf near the monitor, with the most useful slots facing outwards. 4
Printrbot The Printrbot sits, alone and unloved, jealous of its successor the Rostock MAX. Bring a little love and joy into its world by repairing it, replacing the firmware with Repetier, getting a VM set up for it, and generally making it a more useful machine again. 4
Replace USB Hub The current USB hub used by the Fab Lab server sucks. Suggested replacement would be one or two USB2.0 self-powered hubs. If two, one would be mounted on the underside of the bottom shelf near the monitor for flash drives and such, and the other tucked away hidden for machine interfaces. 4
Relocate Pegboard The pegboard hanging on the wall behind the office-side door is a much-appreciated secret donation. However, being behind the door is a less-than-useful location. A good target for this would be on the opposite wall, under the shelf and between the Protomat and the Rostock MAX. 4
Rehang Corkboard The corkboard on the wall hangs from a board, rather than being flush to the wall. This causes the board to swing when bumped. 5
Decorative Work The Fab Lab currently has a sort of forest theme going on. It would be nice to continue the theme by painting the conduits and stanchions deep brown to simulate vines and trunks, put up more vinyl leaves, and paint the ceiling with either a sky pattern or a forest canopy pattern. 5

Important Notes

  • Please keep the door between the Fab Lab and the Commons area closed. Doing so will help ensure that when the heater or air conditioner is running, the Fab Lab maintains an appropriate temperature. Also the AC/Heater for the office space isn't anywhere near efficient enough to cool/heat the main shop area, and we don't want to spend a hojillion dollars letting it try.
  • Please don't use the FabLab as a shortcut between the commons area and the eLab when someone is working in there. There's not a lot of room, and having a parade go by while you're arguing with the printrbot isn't all that much fun.

Pages in category "Fab Lab"

The following 9 pages are in this category, out of 9 total.